价格:未填
供应:99999
发货:3天内
品牌HV 型号PB11C05 最高电压AC 500V V额定发热电流 A用途开关 头部保护等级 产品认证 2．ELECTRICAL CHARACTERISTICS ??性能?格： ITEM ?目 TEST CONDITIONS ???件 PERFORMANCE 性能 2.1 CONTACT RESISTANCE 接??阻 MEASURED AT SMALL CURRENT（100 mA OR LESS）1000HZ 在微小?流（100 mA）以下?? 200mΩ MAX. 200毫?以下。 2.2 INSULATION RESISTANCE ???阻 APPLY A VOLTAGE OF 500V DC SHALL BE APPLIED FOR 1 MIN AFTER WHICH MEASUREMENT BE MADE： （1）BETWEEN CONDUCTORS NOT TO BE CONTACT （2）BETWEEN INDIVIDUAL TERMINALS AND FRAME ?入500V DC ??1分?，按以下接?方法??： （1）不接?的插?之? （2）插??外?之? 100MΩ MIN. 100兆?以上。 2.3 DIELECTRIC STRENGTH 耐?? AC 500V rms（50-60HZ）FOR 1 MIN TRIP CURRENT：0.5mA （1）BETWEEN CONDUCTORS NOT TO BE CONTACT. （2）BETWEEN INDIVIDUAL TERMINLS AND FRAME ?入AC 500V (50-60HZ)??,1分?感度?流?0.5mA,按以下接?方法??： （1）不接?的插?之? （2）插??外?之? WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC. ?有??破?等?常。 3．MECHANICAL CHARACTERISTICS ?械性能?格： ITEM ?目 TEST CONDITIONS ???件 PERFORMANCE 性能 3.1 OPERATING FORCE 作?力 120gf±30gf 3.2 TERMINAL STRENGTH 端子?度 A STATIC LOAD OF 100gf SHALL BE APPLIED TO THE TERMINAL FOR 15 SEC. IN ANY DIRECTION . 在插?前端任意一?方向加100gf力度??,???15秒。 ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED WITHOUT DAMAGE OR EXCESSIVE LOOSENESS OF TERMINALS. 在插?中?有裂?、???常,?足於?械,?器性能。 文件?? DGKD/JS-PB-018 版 本 A / 0 ? ? 共4?，第2? ITEM ?目 TEST CONDITIONS ???件 PERFORMANCE 性能 3.3 DISPLACEMENT OF ACTUATOR （KNOB） 柄 ? 度 A STATIC LOAD OF 9.8 N（1kgf）SHALL BE APPLIED TO THE TOP OF THE ACTUATOR（KNOB） AND THEN DISPLACEMENT SHALL BE MEASURED TO THE DIRECTION OF THE ARROW. 在柄的前端施加9.8N (1kgf)的力度,位移?沿印?的方向上?定。 THE LEVER SHALL HAVE NO SERIOUS DEFORMATION AND FUNCTION IS NORMALLY. 柄部??重?形,可以正常工作。 4．ENDURANCE CHARACTERISTICS(耐久性)： ITEM ?目 TEST CONDITIONS ???件 PERFORMANCE 性能 4.1 MECHANICAL-LIFE TEST 机械寿命 SWITCH SHALL BE SUBJECTED TO 1000,000 CYCLES AT A SPEED OF 15～25 PER MINUTE WITHOUT LOAD. ??在??荷的?件下以每分?15～25回的速度?行1000,000次的??。 1.CONTACT RESISTANCE: ≤5Ω 2.INSULATION RESISTANCE: ≥30MΩ 3.UNDER A VOLTAGE 300V AC(50Hz) WITHOUT DESTROYING AND LOSSING. 4.OPERATING FORCE ±50% SPEC. 5.NO DEFORMATION AND LOOSENESS 1.接??阻：≤5欧 2.???阻：≥30兆欧 3.施加50Hz300V的交流????穿和?孤?象。 4.作?力?化???格值±50% 5.??外观无异常，?合部分?牢固，?固部分????。 ELECTRICAL-LIFE TEST 电气寿命 SWITCH SHALL BE SUBJECTEDTO1000,000 CYCLES AT A SPEED OF 15～25 PER MINUTE UNDER RATING LOAD. ??在额定负荷?件下以每分?15～25回的速度?行1000,000次的??。 4.2 SOLDERABILITY TEST 可焊性?? THE TOP OF THE TERMINALS SHALL BE DIPPED 2mm IN THE SOLDER BATH OF 230±5℃ FOR 3±0.5 SECONDS. 端子?部被浸入?焊池中2mm 深,?度?230±5℃,???3±0.5秒。 (1) THE AREA OF SOLDERABILITY SHOULD BE OVER 75%. 焊接面?要有75%以上. 文件?? DGKD/JS-PB-018 版 本 A / 0 ? ? 共4?，第3? ITEM ?目 TEST CONDITIONS ???件 PERFORMANCE 性能 4.3 RESISTANCE TO SOLDERING HEAT TEST 耐焊性?? SOLDER BATH METHOD: SOLDER TEMPERATURE 250±5℃ IMMERSION TIME 3±0.5 SEC IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD THICKNESS OF PRINTED WIRING BOARD 1.6mm DIMENSIONS OF COMPONENT HOLES IN THE PRINTED WIRING BOARD SHALL. BEING ACCORDANCE WITH THOSE SPECIFIED IN THIS SPECIFICATION. 焊?焊接的???度控制在250±5℃ ，????? 3±0.5秒，於（基板）厚度1.6mm. WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS. ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. 本???形,能?足於?械、?器性能。 4.4 COLD TEST 耐冷?? THE SWITCH SHALL BE STORED AT A TEMPERATURE OF –25±3℃ FOR 48 HOURS.THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE WITHIN 1 HOUR. ??放置在?度–25±3℃中48小?後,再放置常?常?中1小???行??。 1.CONTACT RESISTANCE: ≤100mΩ 2.THE EXTERNAL APPEARANCE JUST LIKE OFTEN CHANGES ,AND CAN PROCEED THE NORMAL CONVERSION ACTION. 1．接触?阻：≤100毫欧 2. 外???常?化，且能?行正常的???作。 4.5 HEAT TEST 耐??? THE SWITCH SHALL BE STORED AT A TEMPERATURE OF 70±2℃ FOR 48 HOURS.THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASURMENT SHALL BE MADE. ??放置在?度70±2℃中??48小?後,再放置正常室?中1小???定。 1.INSULATION RESISTANCE:≥30MΩ 2.THE EXTERNAL APPEARANCE JUST LIKE OFTEN CHANGES ,AND CAN PROCEED THE NORMAL CONVERSION ACTION. 1． ???阻：≥30兆欧 2. 外???常?化，且能?行正常的???作。 4.6 TEMPERATURE VARIETY ?度?化 THE SWITCH SHALL BE STORED AT A TEMPERATURE OF -25℃ AND +70℃ FOR 30 MINUTES, EACH 10 CYCLES OF TRANSITION WITH INTERVALS OF 2～5 MINUTES. ??在-25℃ 和 +70℃的?度下分?放置30分?，?度的?????2～5分?。?10次?圈後，在正常?度下恢?1小?。 THE EXTERNAL APPEARANCE JUST LIKE OFTEN CHANGES ,AND CAN PROCEED THE NORMAL CONVERSION ACTION. 外???常?化，且能?行正常的???作。 4.7 HUMIDITY TEST 恒定?? THE SWITCH SHALL BE STORED AT A TEMPERATURE OF 40±2℃ AND A HUMIDITY OF 90% TO 95% FOR 96 HOURS.THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE WITHIN 1 HOUR. 放置40±2℃的相??度?90%～95%?境中96小?後，再??板放在正常?境1小?後?行??。 1.CONTACT RESISTANCE: ≤100mΩ 2.INSULATION RESISTANCE: ≥30MΩ 3.UNDER A VOLTAGE 300V AC(50Hz) WITHOUT DESTROYING AND LOSSING. 1.??接??阻：≤100毫欧 2.?????阻：≥30兆欧 3.施加50Hz300V的交流????穿和?孤?象。 文件?? DGKD/JS-PB-018 版 本 A / 0 ? ? 共4?，第4? ITEM ?目 TEST CONDITIONS ???件 PERFORMANCE 性能 4.8 STANDARD ATMOSPHERIC CONDITIONS ?????? UNLESS OTHERWISE SPECIFIED.THE STANDARD RANGE OF ATMOSPHERIC CONDITIONS FOR MAKING MEASUREMENTS AND TESTS ARE AS FOLLOWS： （1）AMBIENT TEMPERATURE：5℃ TO 35℃ （2）RELATIVE HUMIDITY: 45% TO 85% （3）AIR PRESSURE: 86Kpa TO 106Kpa 在?有指定的情?下???度、?度、??如下： （1） ?度?5～35℃ （2） ?度?45%～85% （3） ???86Kpa～106Kpa 4.9 PRACTICAL TEMPERATURE RANGE 使用?度?? -10℃～+60℃ 在-10℃～+60℃?度?使用 5.0 CONSERVATION TEMPERATURE 保存?度 THE SWITCHES’STORE CONDITIONS REQUIREMENT AMD STORE TIME LIMIT: 1. THE SWITCHES PACKED IN THE CARTON BOARD BOXES AMD WOODEN BOXES CAN BE TRANSPORTED BY ANY KINDS OF VEHICLES,BUT NEED AVOIDING BEING STRICEN BY RAIN,SNOW AMD MECHANISM. 2. THE SWITCHES SHOULD BE KEPT UNDER THE BELOW CONDITIONS: THE TEMPERATURE IS KEPT WITHIN THE LIMITS OF SUBZERO THEN DEGREE CENTIGRADE TO FORTY DEGREE CENTIGRADE;THE RELATIVE HUMIDITY SHOULD BE NOT MORE THAN EIGHTY PERCENT AMD THERE IS NO ACID ,ALKALI,SULFIDE ,OZONE,ALKALINE AIR AND ANY OTHER POISONOUS GAS AROUND THE STOREHOUSE. ??保存?件要求和期限： 1、 ?有?品的?箱或木箱允?用任何方法??，唯需避免雨雪直接淋?和?械撞?。 2、 ?品?存放在?境?-10～+40℃，相??度不大於80%，周?空?不?有酸、?、硫化物、臭氧、氨?及其它??品有害??的???。 6.0 CHINA OF ORIGIN 原?? MADE IN CHINA. 中??造. 7.0 ROHS COMPLIANT 符合RoHS指令 ON THE RESTRICTION OF THE USE OF CERTAIN HAZARDOUS SUBSTANCES IN ELECTRICAL AND ELECTRONIC EQUIPMENT,THE USE OF PROHIBITED SUDSTANCE IS LIMITED TO: (1)Cd (2)Pb.Hg.Cr(VI).PBB AND PBDE (3)INCLUDE THE RANGE OF THAT RoHS RELEASE. 电子电气设备中限制使用某种特定有害物质,禁用物质允许最大含量值的MCV: (1)Cd 为 (2)Pb.Hg.Cr(VI).PBB AND PBDE为 (3)包括RoHS最新豁免的范围. MEET THE ABOVE REQUIREMENT. 符合要求.